白木印生の dmesgがマニュアルにあった

白木印生の dmesgがマニュアルにあったので盗用してみる。

IXP4xx系の Ethernet MACがそのまま見えているようにみえるので、
IXP425 portがある NetBSDなら CPU, Etherあたりは素直に見えるのかなあ。

USBも NECOHCIだから普通に見えそう。

シリアルはよくわかんないなあ。
タイマーもよくわかんない。

RedBoot(tm) bootstrap and debug environment [ROM]
Red Hat certified release, version 1.94 - built 12:28:34, Apr 14 2005
Platform: Intel Generic Residential Gateway MRL(NV-diag) (XScale) BE
Copyright (C) 2000, 2001, 2002, 2003, 2004 Red Hat, Inc.
RAM: 0x00000000-0x04000000, 0x0001f218-0x03fd0000 available
FLASH: 0x50000000 - 0x52000000, 256 blocks of 0x00020000 bytes each.
== Executing boot script in 3.000 seconds - enter ^C to abort
RedBoot> fis load -d -b 0x00800000 ramdisk.gz
Image loaded from 0x00800000-0x01000000
RedBoot> fis load -b 0x01600000 zImage
RedBoot> go -n
Uncompressing Linux....................................................... done,
booting the kernel.
Linux version 2.4.31-uc0-GBI (root@debian) (gcc version 3.4.4) #1 Thu May 31 13:16:49 JST 2007
CPU: XScale-IXP4xx/IXC11xx revision 1
Machine: Shiraki Jirushi
Warning: bad configuration page, trying to continue
alloc_bootmem_low
memtable_init
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS1,115200 root=/dev/ram0 initrd=0x00800000,8M mem=32M@0x00000000
Calibrating delay loop... 527.56 BogoMIPS
Memory: 32MB = 32MB total
Memory: 22392KB available (1316K code, 245K data, 232K init)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
PCI Autoconfig: Found Bus 0, Device 2, Function 0
PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bfff000
PCI Autoconfig: Found Bus 0, Device 2, Function 1
PCI Autoconfig: BAR 0, Mem, size=0x1000, address=0x4bffe000
PCI Autoconfig: Found Bus 0, Device 2, Function 2
PCI Autoconfig: BAR 0, Mem, size=0x100, address=0x4bffdf00
PCI: bus0: Fast back to back transfers disabled
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xff000003 (irq = 15) is a XScale UART
ttyS01 at 0xff001003 (irq = 13) is a XScale UART
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Universal TUN/TAP device driver 1.5 (C)1999-2002 Maxim Krasnyansky
usb.c: registered new driver hub
host/usb-ohci.c: USB OHCI at membase 0x4bfff000, IRQ 27
host/usb-ohci.c: usb-00:02.0, NEC Corporation USB
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
host/usb-ohci.c: found OHCI device with no IRQ assigned. check BIOS settings!
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.97 (double precision)
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 8192 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 8192K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 232K
Using /lib/modules/2.4.31-uc0-GBI/kernel/ixp425/ixp400-2.0/ixp400.o
Using /lib/modules/2.4.31-uc0-GBI/kernel/ixp425/net-2.0/ixp400_eth.o
ixp400_eth: Initializing IXP400 NPE Ethernet driver software v. 1.4A
ixp400_eth: CPU clock speed (approx) = 527 MHz
ixp400_eth: ixp0 is using NPEB and the PHY at address 0
ixp400_eth: ixp1 is using NPEC and the PHY at address 1
ixp400_eth: Use default MAC address 00:02:b3:01:01:01 for port 0
ixp400_eth: Use default MAC address 00:02:b3:02:02:02 for port 1
ixp400_eth: ixEthMiiLinkStatus failed on PHY0.
Can't determine
the auto negotiated parameters. Using default values.
Welcome to
S n a p G e a r L i n u x
For further information check:
http://www.snapgear.org/
#

http://www.gfi.co.jp/25ji_download/nama/nama_construction_guide_20070608.pdf